MG Midget and Austin Healey Sprite Cooling

MG Midget and Austin Healey Sprite Cooling. Order today from RimmerBros.com. Low Prices and Fast delivery ✈ worldwide! Call ☎ 01522 568000 or ☎ 1-855-746-2767
Part No.: GRID000370

Prices displayed in: GB Pound Euro US Dollar AUD NZD
Part number: B-SMG VERT

For use with 948, 1098 & 1275cc cars with vertical flow radiators upto 1968

Kit Contains:
9" suction fan.
Fan mounting pull throughs
25mm Revotec Electronic fan controller
Earth wire kit
Bolts & fittings
£149.95 ex VAT£179.94 inc UK VAT
Quantity
Part number: B-SMG-VERT-PE

For use with 948, 1098 & 1275cc cars with vertical flow radiators upto 1968

Kit Contains:
9" suction fan.
Fan mounting pull throughs
25mm Revotec Electronic fan controller
Earth wire kit
Bolts & fittings
Usually in stock at our supplier, allow 1 week for delivery
£204.94 ex VAT£245.93 inc UK VAT
Quantity
Part number: B-SMG 1275

For use on post 1968 1275cc cars

Kit Contains:
9" Blowing fan
Laser cut stainless steel fan mounting brackets
25mm Revotec Electronic fan controller
Earth wire kit
Bolts & fittings
£174.95 ex VAT£209.94 inc UK VAT
Quantity
For use on post 1974 1500cc cars

Kit Contains:
9" Blowing fan
Laser cut stainless steel fan mounting brackets
25mm Revotec Electronic fan controller
Earth wire kit
Bolts & fittings
-
£174.95 ex VAT£209.94 inc UK VAT
Quantity
£3.25 ex VAT£3.90 inc UK VAT
Quantity
£2.95 ex VAT£3.54 inc UK VAT
Quantity
£2.95 ex VAT£3.54 inc UK VAT
Quantity
£1.17 ex VAT£1.40 inc UK VAT
Quantity
£1.50 ex VAT£1.80 inc UK VAT
Quantity
£0.75 ex VAT£0.90 inc UK VAT
Quantity
£0.40 ex VAT£0.48 inc UK VAT
Quantity
£2.50 ex VAT£3.00 inc UK VAT
Quantity
£2.50 ex VAT£3.00 inc UK VAT
Quantity
£2.95 ex VAT£3.54 inc UK VAT
Quantity
£15.00 ex VAT£18.00 inc UK VAT
Quantity
Usually in stock at our supplier, allow 1 week for delivery
£21.00 ex VAT£25.20 inc UK VAT
Quantity
£26.70 ex VAT£32.04 inc UK VAT
Quantity
£1.60 ex VAT£1.92 inc UK VAT
Quantity
£1.50 ex VAT£1.80 inc UK VAT
Quantity
Screwed into thermostat and water pump housing

Located at front (carb and pre-’92 EFi engines) or on top (later EFi engines) of
the inlet manifold - all engines except MGB GT V8.
£4.95 ex VAT£5.94 inc UK VAT
Quantity
Out of stock, expected soon. Add to cart and Back Order
£75.00 ex VAT£90.00 inc UK VAT
Quantity
A 10 Row Oil to Air Cooler with 1/2" BSP male thread fittings of a pressed plate design.

As used on many British classics including MGB from 1963 to 1974, and as an optional extra for MGA, MG Midget, Austin Healey Sprite, Classic Mini and many Triumph models.

It is good practice when modifying engines to allow for extra cooling,  engine oil should not get too cool or too hot as this can lead to rapid engine wear. Depending on climate a 10 row Oil Cooler is usually suitable for road use, a 13 row Oil Cooler for fast road/sport, a 16 row Oil Cooler for sport/sprints, and a 19 row Oil Cooler for competition/race. Oil Cooler Installation Kits are available separately, allowing you the choice of cooling depending upon your application, and include ready assembled hoses. We can also supply thermostatic control valves.
£40.00 ex VAT£48.00 inc UK VAT
Quantity
£110.00 ex VAT£132.00 inc UK VAT
Quantity
A 13 Row Oil to Air Cooler with 1/2" BSP male thread fittings of a pressed plate design.

As used on many British classics including MGB from 1963 to 1974, and as an optional extra for MGA, MG Midget, Austin Healey Sprite, Classic Mini and many Triumph models.

It is good practice when modifying engines to allow for extra cooling,  engine oil should not get too cool or too hot as this can lead to rapid engine wear. Depending on climate a 10 row Oil Cooler is usually suitable for road use, a 13 row Oil Cooler for fast road/sport, a 16 row Oil Cooler for sport/sprints, and a 19 row Oil Cooler for competition/race. Oil Cooler Installation Kits are available separately, allowing you the choice of cooling depending upon your application, and include ready assembled hoses. We can also supply thermostatic control valves.
£37.50 ex VAT£45.00 inc UK VAT
Quantity
Not supplied with Oil Cooler Kit.
Prolonged use of a car engine in conditions where the oil cannot reach its correct working temperature will cause sludge formation and crankcase oil dilution, leading to excessive wear especially in the cylinder bores. Optimum engine power will only be delivered at correct temperatures. The elimination of drag in engines caused by cold oil is a most important consideration, especially with a racing engine, revving the engine without a load will not put much heat into the oil and devices for preheating the oil may not be available. It is therefore desirable to control of the oil flow through the cooler by a thermostatic device, set to divert oil to the cooler at 80ºC (although a wide range of settings is available for special applications). This is the minimum temperature required to evaporate and dispel contaminating substances. The bodies of these units are die cast aluminium. Control is by a "waxstat", a mass produced item built to highest standards. They are light enough to be supported by the hoses, however a bracket is supplied with the slightly heavier RB7510, if further restraint is required. The Thermostats should only be used where oil cooling is adequate, the sensing device will suffer permanent damage above 140°C, replacements are available.

Please note :- Only suitable for use with Rubber Hoses (for Braided Hoses Use 1/2" BSP Screw In Thermostat TT29602).
-
£49.00 ex VAT£58.80 inc UK VAT
Quantity
Out of stock, expected soon. Add to cart and Back Order
£20.50 ex VAT£24.60 inc UK VAT
Quantity
Usually in stock at our supplier, allow 1 week for delivery
£53.00 ex VAT£63.60 inc UK VAT
Quantity
£6.00 ex VAT£7.20 inc UK VAT
Quantity
£5.50 ex VAT£6.60 inc UK VAT
Quantity
Usually in stock at our supplier, allow 2 to 4 weeks for delivery
£135.00 ex VAT£162.00 inc UK VAT
Quantity
£98.50 ex VAT£118.20 inc UK VAT
Quantity
Usually in stock at our supplier, allow 1 week for delivery
£385.00 ex VAT£462.00 inc UK VAT
Quantity
Out of stock, expected soon. Add to cart and Back Order
£107.50 ex VAT£129.00 inc UK VAT
Quantity
A cast Brass heater control valve complete with cast brass tap handle. As fitted to; MG Midget and Austin Healey Sprite (1958 to 1974), early Morris Minor, and Austin Healey 100-4. Thread 3/8 inch by 19 TPI (3/8 inch BSP).
-
£10.00 ex VAT£12.00 inc UK VAT
Quantity
Shown as In Stock at our supplier.
Usually ships in 2-3 working days.
£26.90 ex VAT£32.28 inc UK VAT
Quantity
£90.00 ex VAT£108.00 inc UK VAT
Quantity
Usually in stock at our supplier, allow 4 to 6 weeks for delivery.
£20.00 ex VAT£24.00 inc UK VAT
Quantity
£2.65 ex VAT£3.18 inc UK VAT
Quantity
Customer Comments
"Excellent site well laid out and prices are very good." Customer Comment
Product Description

MG Midget and Austin Healey Sprite Cooling